The Wonders of Recycling.

Over the last few days I had the pleasure of running a program held at the Earthwise Community Association in Subiaco, focussing on the use of basic woodworking hand skills to create wooden products from timber which has been discarded on roadside cleanups.

Diverting discarded timber and wooden furniture from landfill.

Much of the timber resources I gathered up for the program by doing a kerbside crawl in a neighbouring suburb on the morning before. What a treasure trove! This included an old jarrah desk, made of nice wide boards. The current cost of the timber in this desk would be over $250. There it was waiting to go off into landfill. Crazy. We put much of it to good use. This picture shows some of the wonderful resource obtained from a quick drive around a local cleanup area in progress.

The program was sponsored by the Mindarie Regional Council, Western Australia's largest Waste Management Authority. The MRC manages the disposal of about 350,000 tonnes of waste generated each year by people living in its seven member Local Government Councils. These are the Cities of Joondalup, Perth, Stirling, Wanneroo, and the Towns of Cambridge, Victoria Park and Vincent.

The series of workshops run over 3 days were intended to help the participants understand how so much of this roadside discarded timber and furniture can be diverted from landfill and given new life as new pieces of furniture or as functional wooden items. This also involved the participants learning basic woodworking skills in order to know how to utilise some of this huge resource.

Utilising timber and wooden furniture from the kerbside cleanups will often involve the demolition and cleaning up of the timber first. So we started out with people learning how to use pincers, claw hammers and pinch bars to separate components and remove the nails.

Session 1 - Making a kitchen chopping board

The project for the first session was to make a kitchen chopping board. Some great wide pine boards were obtained from a large packing crate. More were obtained from some old bookshelves. There were some jarrah boards, ex 8"x1", which had previously been ridge pieces from a house. A discarded imported kichen benchtop provided a solid laminated timber from something like plantation oak. The 12 participants learned how to use panel saws on sawstools to cut their pieces to length first. Then it was on to how to use a hand plane to plane the faces, shoot the edges and then shoot the ends square. The arises were chamfered with block planes, a small amount of hand sanding followed, and then olive oil was applied to the finished chopping boards.

While some found muscles they hadn't used before, all were delighted to take their piece of grotty looking timber on a journey to new life as a functional kitchen implement which will last for generations. Along the way some basic woodworking skills and understandings of timber were gained. For many this was a new experience, and opened up new possibilities for the diverting of material which would have previously been heading for landfill.

Session 2: Making a book shelf/DVD rack.

Based on a plan from a 1946 woodworking text book, the project for the second session was the making of a small bookshelf, modified to also be a good size for use as a DVD rack. Wider boards were used to make the ends, and several people used jarrah obtained from that desk. The timber used for the horizontals I had previously machined from old 4"x2" jarrah and blackbutt rafters and flooring. Nice timber. The 10 participants learned how to the use a tenon saw, marking knife, marking gauge, sliding bevel and chisels to mark out and cut the tenons and mortises. While none of the bookshelves were actually completed by the end of the session, they were just about there. A couple of people borrowed some chisels just to finish off their mortises at home. It had involved the learning of many new skills, and some nice bookshelves will yet be completed.

Session 3: Making a wooden Spoon.

This session is always fun. The 6 participants used an array of timber to make their spoons. We recycled bits of a barbeque trolley, flooring offcuts, and a piece of 3"x2" wall stud for this project. The participants learned how to use gouges, scrapers, spokeshaves, coping saws and rasps to make their spoons. A bit of sanding and the application of olive oil completed the project. Each spoon was an individual expression of its maker, and were a fantastic collection of beautiful designs and functional pieces which will last for many many years - again from timber diverted from landfill!

At the start of Day 2, I had 28 planes to sharpen! I was very pleased it only took me 80 minutes!

The message behind the activities.

This program was a heap of fun, but had a serious message behind it. One of the key educational messages for the participants is this: It is time we were a lot less wasteful and more conscious of where all that kerbside cleanup material ends up.

Landfill is a growing problem for us all, and there is no need for us to throw out so much wonderful timber which can be utilised - and diverted from landfill - once we appreciate it's potential and have the basic skills to use it.

Session Four: Making New from Old.

The last session was a full day, a Saturday, and an opportunity for the participants to make whatever they wanted to. I arrived early to get organised, before the group arrived. While preparing for the day, I was knocking apart some discarded drawers to get the timber from the drawer sides and faces. I was thinking how good it was that the material (pine) was all dressed to a nice consistent size. So I knocked up an egg rack in half an hour. When the mob arrived, the egg rack provided some inspiration, and sure enough another egg rack was made from some drawer sides before the day was out. Some participants made jarrah spoons and kitchen spatulas from bits of barbeque trolley, or continued on working on their bookshelves. There was also a fantastic combination bench hook and shooting board made from an old aloes drawer front, and a jarrah photo frame made from timber I had previously machined from an old rafter. A small old ledged jarrah door was made into a table top with legs for the table made from a discarded pine Ikea bed frame. A wonderful piece of which the creators were very pleased!

All in all a very successful program, and a heap of fun! The smiles say it all. Peg's yummy soup kept us smiling too.

The message also came through clearly about some simple ways to utilise timber which was discarded and destined for land fill until it put to a range of other uses by the workshop participants.

Special thanks to Peg, George and the Earthwise mob for their friendly hospitality, and demonstrated committment to community and responsible living on this Planet.

Let's hope we get to offer more of these workshops...

A Saw Stool on Steriods!

Those who have worked with me know how much I value traditional Saw Stools. I use them in the workshop and out on the job all the time. In fact I am lost without them! I usually have several sets, some low ones at around 21” high and some taller ones at 30” high.

I am not talking about those crappy folding metal and pine things, which wobble around and carry warning stickers saying you should not stand on then. I am referring to properly made traditional saw stools. Traditionally made from jarrah in Western Australia, these are rigid and can carry considerable loads. I have in use some that are well over 50 years old and which have worked hard all their lives. These type of saw stools were standard equipment for carpenters, joiners and cabinet makers for generations.

I had a big job to do recently, which involved working on site in Kalamunda for 3 weeks solid. I took a portable jarrah work bench with me, as there was a fair bit of bench work to do over those 3 weeks. Of course I also needed to use 2 pairs of low saw stools and 2 pairs of taller saw stools on site for that period as well.
While I worked on the job, I got thinking: How can I create a saw stool X workbench hybrid, which would be more portable than my portable work bench?

So I have played with the idea, and the result is a Saw Stool which looks like it has been on steroids:

View of the beast - a hybrid between a saw stool and a bench.

Here are the specifications:

Height: 880mm. The legs have a 10 degree splay to the ends and to the sides.
Length: 980 (plus tail vice outer cheek equals 1030mm overall.
Width: Pine 220mm, including jarrah front edge equals 260mm.
Tail vice: Maximum bite 240mm
· Minumum bite between dog holes: 240mm
· Maximum bite between dog holes: 1040mm.
Front vice: Maximum bite 140mm
· Minimum bite between dog holes: 110mm
· Maximum bite between dog holes: 390mm.

View with the Tail Vice extended.

A 25mm square Tuart guide rod maintains the orientation of the vice cheek with the single vice screw.

Almost whole thing is made from recycled salvage material :
· Pine top – from a 10” x 3” solid pine beam.
· Legs, rails, and other odds and sods – from some 3”x2” jarrah wall studs.
· “Breadboard ends” - from an old jarrah door sill. · Jaw cheeks of the front and tail vices – from a jarrah 8”x2” ceiling joist.
· Vice handles made from Peppermint (Agonis flexuosa) I milled years ago.
· Tail vice guide rod made from a piece of Tuart (Eucalyptus gomphocephala) leftover from the making of the Endeavour Replica.
· The tail vice screw and front vice are those imported ones from China or Taiwan, bought from my local woodworking shop. The front vice is the smaller of the two models available locally, and is pretty disappointing. Its guide rods and screw are not square to the metal vice front and rear, and are barely parallel. However the tail vice screw is a ripper. These metal components cost less than $100 in total. I put the additional bit of jarrah onto the front side of the pine to beef up the work area a bit and provide a more durable front edge to the work area. The only reason I used pine was to help keep down the weight!

Putting the beast to the test.

I had a job to do on a different site straight after I have made the beast, so had a good chance to road test it. I was not disappointed. It worked brilliantly.

This job involved removing a customer's front entry joinery, then installing and modifying a beautiful old piece of art deco joinery obtained from a demolished building and adding two more art deco side light sashes either side. This involved lots of tricky hand work on site, where the beast proved to be invaluable.

The holding capacity of the dogs worked really well, and both vices worked well holding components as I made them.

The only change I will make will be to add a removable shelf underneath, sitting across the spreaders, as there is nowhere to put tools being used.

Fireplace Surround for a Heritage Building Restoration.

These kind of gigs don't come around very often...



Earlier this year I had the privilege of making a fireplace surround for "Hill 60", a heritage building being restored in Rivervale. Working from only 6 old photographs, the task was to re-instate the fireplace surround. The original had gone missing some years ago while the building was derelict.

At over 9.5 feet tall and 5.5 feet wide, it was made in 10 components which finally went together beautifully like a jigsaw on site after 3 months of work.

These four photos by NK Photography.

I asked well known Woodcarver Jenny Scrayen to work with me on the more complex carving aspects, like the dragons on the columns, the front panel, and the floral wreath on the pediment. It was a pleasure to work with such a talented person. Thanks Jenny. I did all the planning, joinery, turning, basic carving, and finishing. It is all made from jarrah (Eucalyptus marginata) primarily using traditional woodworking techniques.

Making this stuff is so good for the soul...

and what a joy this job was!